ADTRAN 1200214L1 Especificaciones Pagina 46
- Pagina / 176
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 3. Operation
3-6 IQ Probe User Manual 61200214L1-20
VT-100 Terminal Connection and Operation
To control the IQ Probe using a VT-100 terminal, follow this procedure:
1. Set the IQ Probe baud rate to match the terminal through the front
panel (maximum rate is 38.4k). Select 1 C
ONFIG
, then 4 C
ONTROL
P
ORT
.
2. Using the ADTRAN-provided VT-100 terminal adapter, connect the
COM port of a VT-100 compatible terminal or equivalent to the eight-
pin modular jack labeled Control on the rear of the IQ Probe. This
connection is used for both local and remote configuration.
3. Open the connection and press
Enter
repeatedly until the L
OGIN
M
ENU
appears (Figure 3-3 on page 3-7).
4. Select L
OCAL
L
OGIN
to configure the IQ Probe unit connected to the
terminal.
5. Select R
EMOTE
L
OGIN
to configure a remotely located IQ Probe unit.
6. For remote applications, at the remote DLCI prompt, enter the outgo-
ing DLCI (see the following note) by pressing
1
, then
Enter
, entering
the DLCI number, and pressing
Enter
again.
7. Next, select B
EGIN
R
EMOTE
S
ESSION
by pressing
2
and
Enter
. When
entering the DLCI for a remote application, enter the DLCI associated
with the local unit that you are logged in to (not the far end DLCI).
8. Enter the password. The factory default password is adtran. The
main menu will appear (Figure 3-4 on page 3-7).
9. Make selections by entering the number corresponding to the chosen
parameter. Press
ESC
to return to the previous screen.
If the wrong DLCI is entered or a network problem exists, the
screen freezes at the Press any key to continue
prompt. Press
CNTL + L
twice to return the unit to the Login
screen.
In the upper right-hand corner of the VT-100 screen, LOCAL or
REMOTE is displayed, indicating which unit the current screen
represents. See Figure 3-3 on page 3-7.
- IQ Probe 1
- Digital Services 7
- Save These Instructions 12
- Table of Contents 15
- List of Figures 25
- List of Tables 27
- Introduction 29
- UNDERSTANDING FRAME RELAY 30
- SNMP MANAGEMENT 31
- DIAL BACKUP OPERATION 32
- INTERFACE CARD OPTIONS 33
- 4-Wire Switched 56 DBU Card 33
- V.34 DBU Card 33
- ISDN DBU Card 33
- DCE Card 33
- Chapter 1. Introduction 34
- Installation 35
- Power Up 36
- REAR PANEL 37
- Chapter 2. Installation 38
- DBU Interface Card Slot 39
- DCE Interface 39
- DTE Interface 39
- LAN 10BaseT Interface 40
- Control Port 40
- Operation 41
- Numeric Keypad 42
- Next, Prev, Add, Delete 42
- Chapter 3. Operation 43
- LED Descriptions 44
- FRONT PANEL OPERATION 45
- CNTL + L 46
- Local Login Via Telnet 48
- Enter to continue… 49
- Remote Login Via Telnet 51
- ANY KEY TO CONTINUE 53
- IQ PROBE MENU STRUCTURE 55
- MAIN MENU 55
- Applications 57
- Baud Rate 58
- Control Port Mode 58
- Out-of-Band Management 59
- In-Band Management 61
- IP Address 62
- Chapter 4. Applications 64
- ANAGEMENT 64
- DIAL BACKUP APPLICATION 67
- AUTO DBU Enable 68
- With PVC Inactive: Enable 68
- Configuration Overview 71
- DTE Port Configuration 77
- Frame Relay Options (FR OPTS) 80
- Always On 82
- Follows Network (FOLLOW NET) 82
- Configuring the DCE Port 83
- Management DLCI 1 and 2 Mode 86
- PVC Options (PVC CONFIG) 87
- Disabled 90
- Dial Backup Configuration 91
- Auto DBU 94
- DBU Options 94
- DBU Criteria 95
- DBU Timers 96
- Tone/Pulse 97
- Max Baud Rate 97
- Sync/ Async 97
- Switch Type 97
- Call Screening 98
- System Configuration 99
- Subnet Mask 100
- Read Community (RD COMMUNITY) 101
- Trap Mgr Options 101
- Add (ADD key on front panel) 102
- Protocols 1 and 2 103
- System Time/Date 103
- LEDs Reflect 104
- USING THE FRONT PANEL 104
- Statistics 105
- Hot Keys 107
- DTE Port Statistics 108
- Chapter 10. Statistics 109
- DCE Port Statistics 111
- ONFIGURATION 113
- Layer 3 Statistics 116
- Top Talker 120
- DBU Port Statistics 121
- DLCI Statistics 125
- DLCI List 130
- System Statistics 131
- Control Signal Status Screen 133
- VERSION CHKSUM 136
- VER 601a 3F34 136
- Chapter 11 137
- PVC Loopback 138
- Chapter 11. Testing 139
- PVC Active/Inactive/Undefined 140
- Test Active/No Test Active 140
- TATISTICS 141
- Pings Transmitted (PINGS TX) 142
- Ping Responses (PINGS RX) 142
- Chapter 12 143
- Appendix A 145
- Appendix A. Pinouts 146
- Specifications Summary 153
- Acronyms and Abbreviations 155
- Glossary 159
- Appendix D. Glossary 160
- Numerics 171
- Post-Sale Support 175
- Repair and Return 175
Relacionado con productos y manuales para Redes ADTRAN 1200214L1
Redes ADTRAN SLC-5 U-BR1TE III Especificaciones
(12 paginas)
(12 paginas)
Redes ADTRAN TSU 120 Manual de usuario
(143 paginas)
(143 paginas)
Redes ADTRAN 1500 Manual de usuario
(27 paginas)
(27 paginas)
Redes ADTRAN Quad T1 IMA Guía de instalación
(46 paginas)
(46 paginas)
Redes ADTRAN 6330 Manual de usuario
(4 paginas)
(4 paginas)
Redes ADTRAN 600 SERIES Manual de usuario
(72 paginas)
(72 paginas)
Redes ADTRAN TSU LT Manual de usuario
(77 paginas)
(77 paginas)
Redes ADTRAN MX2800 Manual de usuario
(200 paginas)
(200 paginas)
Redes ADTRAN 1204002L1 Manual de usuario
(183 paginas)
(183 paginas)
Redes ADTRAN Cable T1 ESF CSU ACE Manual de usuario
(66 paginas)
(66 paginas)
Redes ADTRAN ATLAS 810 Plus Especificaciones
(188 paginas)
(188 paginas)
Redes ADTRAN T3SU 300 Manual de usuario
(141 paginas)
(141 paginas)
Redes ADTRAN T200 FNID Guía de usuario
(16 paginas)
(16 paginas)
Redes ADTRAN Tracer TRACER 2 x E1 Manual de usuario
(62 paginas)
(62 paginas)
Redes ADTRAN Express 3110 Manual de instrucciones
(116 paginas)
(116 paginas)
Redes ADTRAN Quad T1 IMA Manual de usuario
(4 paginas)
(4 paginas)
Redes ADTRAN Express 3000 SP Información técnica
(150 paginas)
(150 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales