ADTRAN TA 544 Manual de instrucciones Pagina 57
- Pagina / 162
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Total Access 544R System Manual Section 4 SHDSL RCU ATM User Interface Guide
61200704L2-1B © 2003 ADTRAN, Inc. 57
L2 PROTOCOL (SHDSL) > PROTOCOL> ATM
Asynchronous Transfer Mode allocates bandwidth on demand, automatically adjusting the network
capacity to meet the system needs. Fixed-length cells (53 octet) require lower processing overhead and
allow higher transmission speeds than traditional packet switching methods. ATM uses five octet headers
in each fifty-three octet cell to match cells with specific virtual channels to which they belong.
L2 PROTOCOL (SHDSL - ATM) > CONFIG
Configure the L2 Protocol parameters for the SHDSL interface using ATM protocol.
L2 PROTOCOL (SHDSL - ATM) > CONFIG > ATM CONFIG
Use the ATM config menu to set the parameters listed below.
L2 PROTOCOL (SHDSL - ATM) > CONFIG > ATM CONFIG > IDLE CELLS
The Idle Cells format must be configured for either ATM FORUM (UNASSIGNED) or ITU (IDLE). Configuring
this setting incorrectly for a particular circuit will cause poor performance at the ATM Layer. The default is
ATM FORUM (UNASSIGNED).
L2 PROTOCOL (SHDSL - ATM) > CONFIG > ATM CONFIG > DATA SCRAMBLING
DATA SCRAMBLING can be ENABLED or DISABLED for cell traffic. Configuring this setting incorrectly for a
particular circuit will cause poor performance at the ATM Layer.
L2 PROTOCOL (SHDSL - ATM) > CONFIG > ATM CONFIG > HEC COSET
Header Error Control is located in the last (5th) byte of the ATM cell header that checks for cell integrity
only. The Coset polynomial is applied to the received HEC for comparison with the HEC generated
internally. HEC errors may be detected after synchronization any bit errors detected will prompt that cell
be dropped. The choice are
ENABLED or DISABLED. The default is ENABLED.
L2 PROTOCOL (SHDSL - ATM) > CONFIG > PVC CONFIG
Configure up to six ATM PVCs from this menu.
L2 PROTOCOL (SHDSL - ATM) > CONFIG > PVC CONFIG > NUM
Displays the index number for the PVC entry.
The setting must match the configuration setting of the ATM switch or DSLAM at the other
end of the circuit.
- TOTAL ACCESS 544R 1
- Trademarks 2
- To the Holder of the Manual 2
- About this Manual 2
- Revision History 3
- Conventions 3
- Safety Instructions 4
- Services 7
- Notary Public 8
- My commission expires: 8
- Product Warranty 10
- Product Registration 10
- Table of Contents 13
- SYSTEM DESCRIPTION 15
- 1. SYSTEM OVERVIEW 16
- Firmware Updates 16
- Terminal Menu 16
- 2. FEATURES AND BENEFITS 16
- Configuration and Management 16
- Software Upgradeable 17
- Network Interface 17
- LAN Interface 17
- Protocol Support 17
- ATM Support 18
- Routing Capability 18
- Security 18
- Integrated Components 18
- ENGINEERING GUIDELINES 19
- 1. POWER REQUIREMENTS 20
- Front Panel LEDs 20
- NTWK Connection (RJ-48C) 21
- CRAFT Port (RJ-48C) 21
- AC Power Connection 22
- 4. DB-9 TO RJ ADAPTER 23
- NETWORK TURNUP PROCEDURE 25
- 1. INTRODUCTION 26
- 2. TOOLS REQUIRED 26
- Contents of ADTRAN Shipment 26
- 4. GROUNDING INSTRUCTIONS 27
- 6. MOUNTING OPTIONS 28
- 1. SYSTEM INFO 30
- SYSTEM INFO > SYSTEM NAME 30
- SYSTEM CONFIG 32
- SYSTEM CONFIG > MANAGEMENT 32
- SYSTEM UTILITY 46
- ERVER FILENAME field 47
- ERMINAL MODE (see page 40) 49
- Figure 4. Interfaces Menu 53
- SHDSL config 54
- ON or OFF. The 55
- L2 PROTOCOL 56
- L2 PROTOCOL (SHDSL) 56
- ATM FORUM (UNASSIGNED) 57
- > MODE 60
- AP: TX CELLS 60
- L2 PROTOCOL (ETH) 63
- Figure 6. Bridge Menu 66
- INTERFACE menu entries 66
- ROUTER > CONFIG 68
- OUTER > CONFIG > ROUTES 71
- FR 0 . . . FR 9 74
- SECURITY 83
- SECURITY > FILTERS 84
- SECURITY > RADIUS SERVER 87
- 0.0.0.0 88
- ERVER. The default is 89
- ERVER without a response 89
- ATM 90
- Total Access 3000 90
- DETAIL LEVEL PROCEDURES 95
- Introduction 101
- Prerequisite Procedures 101
- Tools and Materials Required 101
- Follow-up Procedures 103
- Security Levels 105
- DDRESS menu 112
- DLP-6 Telnetting to the Unit 115
- TATUS window 122
- TATUS field 126
- Follow-up Procedure 134
- Command Line 137
- ADTRAN UTILITIES 149
- 1. TELNET UTILITY 150
- Session Menu 150
- Edit Menu 152
- Options Menu 152
- Capture Menu 152
- Help Menu 152
- 2. VT100 UTILITY 153
- Port Menu 154
- 3. TFTP SERVER 155
- Server Menu 156
- Print Log 156
- 4. STATUS FIELD 157
- 5. METER FIELD 157
- 6. LOG FIELD 157
- CONTENTS 159
- SNMP manager 160
- 2. MIB COMPILATION ORDER 161
Relacionado con productos y manuales para Redes ADTRAN TA 544
Redes ADTRAN MX2800 Manual de usuario
(220 paginas)
(220 paginas)
Redes ADTRAN MX3216 Especificaciones
(190 paginas)
(190 paginas)
Redes ADTRAN T200 FNID Especificaciones
(76 paginas)
(76 paginas)
Redes ADTRAN Stub Routing Guía de usuario
(132 paginas)
(132 paginas)
Redes ADTRAN 1200214L1 Especificaciones
(176 paginas)
(176 paginas)
Redes ADTRAN SLC-5 U-BR1TE III Especificaciones
(12 paginas)
(12 paginas)
Redes ADTRAN TSU 120 Manual de usuario
(143 paginas)
(143 paginas)
Redes ADTRAN 1500 Manual de usuario
(27 paginas)
(27 paginas)
Redes ADTRAN Quad T1 IMA Guía de instalación
(46 paginas)
(46 paginas)
Redes ADTRAN 6330 Manual de usuario
(4 paginas)
(4 paginas)
Redes ADTRAN 600 SERIES Manual de usuario
(72 paginas)
(72 paginas)
Redes ADTRAN TSU LT Manual de usuario
(77 paginas)
(77 paginas)
Redes ADTRAN MX2800 Manual de usuario
(200 paginas)
(200 paginas)
Redes ADTRAN 1204002L1 Manual de usuario
(183 paginas)
(183 paginas)
Redes ADTRAN Cable T1 ESF CSU ACE Manual de usuario
(66 paginas)
(66 paginas)
Redes ADTRAN ATLAS 810 Plus Especificaciones
(188 paginas)
(188 paginas)
Redes ADTRAN T3SU 300 Manual de usuario
(141 paginas)
(141 paginas)
Redes ADTRAN T200 FNID Guía de usuario
(16 paginas)
(16 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales