ADTRAN 1200287L1 Manual de usuario Pagina 81
- Pagina / 204
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 4. Status
61185001L1-1 MX2810 M13 User Manual 4-7
Card Comm
This field displays the current state of the communication link
between the two controller cards. OK indicates that the cards are
communicating; F
AILURE
indicates that the cards are not able to
communicate with each other. If there is only one card installed,
N
ON
-R
EDUNDANT
is displayed.
DS2 STATE
This field displays the current state of each of the seven DS2s.
Possible states are listed in the following chart:
T1/E1 STATE
The field displays the current state of the individual T1s or E1s.
Possible states are listed in the following chart:
Condition Description
OK The DS2 is not receiving alarms.
LOF The unit detects framing loss across the DS2.
RAI The unit is receiving an RAI (yellow) alarm across
the DS2. This alarm is a signal sent back toward the
source of a failed transmit circuit. The X-bit is set to
zero.
AIS The unit is receiving an AIS (blue) alarm condition
from the network across the DS2. AIS alarms occur
when the unit receives unframed all ones.
Condition Description
OK The T1/E1 is ready to pass data.
LOS The unit has lost the Rx signal on the T1/E1.
XCV The unit is receiving excessive code violations
across the T1/E1, exceeding the configured
threshold (see XCV Threshold on page 3-4).
- M13 Multiplexer 1
- User Manual 1
- Trademark Information 2
- Service Type REN FIC USOC 3
- Warranty and Customer Service 6
- Table of Contents 10
- List of Figures 13
- List of Tables 15
- Introduction 17
- T3 OVERVIEW 18
- Chapter 1. Introduction 19
- AVAILABLE OPTIONS 20
- Installation and Operation 23
- Power Up 24
- Power Requirements 25
- RACKMOUNT INSTALLATION 27
- Connecting the Breakout Panel 27
- Rear View 28
- Front View 28
- DSX-3 Interfaces 30
- DSX-1/E1 Interfaces 30
- Power Connection 30
- FRONT PANEL 31
- ACO Buttons 31
- LED Descriptions 31
- Craft Port 35
- Configuration 39
- Chapter 3. Configuration 40
- NETWORK INTERFACE 41
- DS3 Configuration 41
- Protection Configuration 43
- Miscellaneous 43
- DS2 Configuration 43
- T1/E1 INTERFACE 44
- T1/E1 State 44
- T1/E1 Line Coding 46
- T1/E1 Line Length 46
- T1/E1 Loopback Detection 47
- T1/E1 Circuit Protection 48
- T1/E1 Line Identification 48
- XCV Threshold 49
- SYSTEM MANAGEMENT 50
- Management Options 50
- Alarm Relays 51
- SNMP Management Options 54
- System Security 59
- Date & Time 63
- ONFIGURATION 65
- UTILITIES 67
- Loading Default Settings 68
- Updating Software 68
- Utilities 71
- Resetting the System 73
- Chapter 4 75
- DS3 STATE 75
- Rx Framing 75
- Chapter 4. Status 76
- POWER SUPPLY STATE 78
- SYSTEM STATE 79
- Card A/Card B 80
- Protection 80
- Card Comm 81
- DS2 STATE 81
- T1/E1 STATE 81
- ACKNOWLEDGE ALARMS (ACO) 82
- Statistics 83
- DS3 Statistics 84
- Chapter 5. Statistics 85
- DS2 Statistics 91
- T1/E1 Statistics 93
- PROTECTION SWITCH STATISTICS 94
- Loopbacks 97
- T1/E1 LOOPBACKS 98
- Tributary 98
- Codec Line/Net 100
- Remote Loopback 100
- CSU Loopback 101
- CSU Loopback w/BERT 101
- Line BERT 102
- Line Loopback 103
- DS3 LOOPBACKS 103
- Digital Loopback 104
- Network Loopback 104
- Remote all T1/E1 105
- DS2 LOOPBACKS 105
- DS2 Network 106
- Circuit Redundancy 107
- NON-REDUNDANT MODE 108
- CIRCUIT FAILURE RECOVERY MODE 109
- Chapter 7. Circuit Redundancy 110
- Power Loss Recovery 111
- NON-REDUNDANT POWER MODE 112
- POWER SUPPLY RECOVERY MODE 113
- BATTERY BACKUP MODE 115
- Transaction Language 1 (TL1) 117
- TL1 MESSAGES 120
- TL1 Responses 121
- TL1 COMMANDS 127
- ALW-MSG-{EQPT 127
- CANC-USER; 128
- INH-MSG-{EQPT 129
- RTRV-HDR; 130
- RTRV-VER; 130
- RTRV-SYS; 130
- RTRV-USER-SECU; 130
- RTRV-ALM-{EQPT 130
- RTRV-COND-{EQPT 132
- TL1 Autonomous Messages 133
- TL1 ERROR CODES 139
- TL1 Editing 139
- Acceptance Test Procedure 153
- (TRAFFIC READINESS) 168
- MX2810 ATP CHECKLIST/SIGN-OFF 169
- Appendix B 171
- Appendix B. Pinouts 172
- DSX1/E1 Amp connectors 173
- Specifications Summary 175
- Acronyms/Abbreviations 179
- Glossary 183
- Appendix E. Glossary 184
Relacionado con productos y manuales para Redes ADTRAN 1200287L1
Redes ADTRAN 1204002L1 Manual de usuario
(171 paginas)
(171 paginas)
Redes ADTRAN TA 544 Manual de instrucciones
(162 paginas)
(162 paginas)
Redes ADTRAN MX2800 Manual de usuario
(220 paginas)
(220 paginas)
Redes ADTRAN MX3216 Especificaciones
(190 paginas)
(190 paginas)
Redes ADTRAN T200 FNID Especificaciones
(76 paginas)
(76 paginas)
Redes ADTRAN Stub Routing Guía de usuario
(132 paginas)
(132 paginas)
Redes ADTRAN 1200214L1 Especificaciones
(176 paginas)
(176 paginas)
Redes ADTRAN SLC-5 U-BR1TE III Especificaciones
(12 paginas)
(12 paginas)
Redes ADTRAN TSU 120 Manual de usuario
(143 paginas)
(143 paginas)
Redes ADTRAN 1500 Manual de usuario
(27 paginas)
(27 paginas)
Redes ADTRAN Quad T1 IMA Guía de instalación
(46 paginas)
(46 paginas)
Redes ADTRAN 6330 Manual de usuario
(4 paginas)
(4 paginas)
Redes ADTRAN 600 SERIES Manual de usuario
(72 paginas)
(72 paginas)
Redes ADTRAN TSU LT Manual de usuario
(77 paginas)
(77 paginas)
Redes ADTRAN MX2800 Manual de usuario
(200 paginas)
(200 paginas)
Redes ADTRAN 1204002L1 Manual de usuario
(183 paginas)
(183 paginas)
Redes ADTRAN Cable T1 ESF CSU ACE Manual de usuario
(66 paginas)
(66 paginas)
Redes ADTRAN ATLAS 810 Plus Especificaciones
(188 paginas)
(188 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.090 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales