ADTRAN T200 FNID Especificaciones descargar pdf (Pagina 3)

61184002L3-5B 3

WARNING

The 10/100baseT interface and DS3 interfaces

MUST NOT be metallically connected to

interfaces which connect to the Outside Plant or

its wiring. These interfaces are designed for use

as intra-building interfaces only. The addition

of Primary Protectors is not sufficient protection

in order to connect these interfaces metallically

to OSP wiring.

NOTE

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following

conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any

interference received, including interference

that may cause undesired operation.

Changes or modifications not approved by

ADTRAN could void the user’s authority to

operate this equipment.

NOTE

The Installation instructions found in the text

below are written under the assumption that

either the Total Access OPTI-3 rackmount or

wallmount chassis (P/N 1184003L1 and

1184001L1 respectively) have been properly

installed (including power, alarm, and data

connections).

The OCM plugs directly into the Total Access OPTI-3

RMC or WMC. Both chassis provide two OCM slots.

Fiber Connection and Physical Installation

The Total Access OPTI-3 RMC provides two OCM

slots that are side by side. See Figure 4. The left slot

is slot A and the right slot is slot B. The Total Access

Code Input Output

Power Code (PC) F C

Telecommunication Code (TC) – –

Installation Code (IC) A –

Table 1. Compliance Codes

• Three audible alarm outputs including Critical,

Major, and Minor (RMC only)

• Three visual alarm outputs including Critical,

Major, and Minor (RMC only)

• –20 VDC to –60 VDC input voltage range

• +20 VDC to +60 VDC input voltage range

• Power consumption between 7 and 10 watts

(typical) per OCM

• Operating temperature range of −40°C to +65°C

(installed in RMC)

• Operating temperature range of −40°C to +50°C

(installed in WMC)

• Storage temperature range −40°C to +85°C

• Relative humidity up to 95 percent,

noncondensing

• NEBS Level 3, GR-1089-CORE, GR-63-CORE

and UL 60950 compliant

• Meets applicable optical and SONET standards

(GR-253, T1.101, T1.105.xx)

2. INSTALLATION

C A U T I O N

SUBJECT TO ELECTROSTATIC DAMAGE

OR DECREASE IN RELIABILITY.

HANDLING PRECAUTIONS REQUIRED.

After unpacking the unit, inspect it for damage. If

damage is noted, file a claim with the carrier, then

contact ADTRAN

Customer Service. Refer to the

Warranty and Customer Service section of this

practice.

Compliance

Table 1 provides the compliance codes for the Total

Access OPTI-3 Controller Module. The OCM

complies with the requirements covered under UL

60950, and is intended for installation in restricted

access locations only in Type “B” or “E” Enclosures.

1184003L1

RMC

OPTI-3

ENABLE

TESTAPS ACO

1184002L3

CRAFT

STATUS

OPTICS

DS3-1

DS3-2

DS3-3

ACO

OPTI-3

ENABLE

TESTAPS ACO

1184002L3

CRAFT

STATUS

OPTICS

DS3-1

DS3-2

DS3-3

ACO

Figure 4. OPTI-3 RMC

Slot A

(working card)

Slot B

(protect card)

1 2 3 4 5 6 7 8 ... 75 76

Comentarios a estos manuales

Sin comentarios

ADTRAN T200 FNID Especificaciones Pagina 3

Comentarios a estos manuales

Relacionado con productos y manuales para Redes ADTRAN T200 FNID