ADTRAN MX2800 M13 Manual de usuario Pagina 62
- Pagina / 198
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
MX2800 M13 Multiplexer User Manual
3-20 61200290L1-1H
Table 3-3 provides trap descriptions.
Table 3-3. Trap Descriptions
Trap If enabled, the unit issues a trap when...
Controller Traps
Protection Switch The controller cards switch.
Card Removed A controller card has been removed.
Card Failure A controller card has failed.
Communication
Fail
The controller cards can no longer communicate with each other.
Max Switches The Max Switch Threshold is reached. For more information, refer to
“Maximum Switch Threshold” on page 3-6.
Power Supply Alarm Traps
Card Removed The power supply card has been removed.
Malfunction The power supply card is no longer working and the unit has switched to the
backup power supply or battery backup.
Card Failure The power supply card has failed.
Power Low The power supply’s output level is abnormally low.
Bat. Backup Act Battery charger has lost its AC power source.
Battery Low Battery backup has reached an energy point insufficient to supply the unit
with power.
Temperature High The power supply card is getting too hot.
Temperature
Critical
The power supply card temperature is so high that it may suffer damage.
DS3 Alarm Traps (Near-End Active and Standby Cards)
LOS The controller card has lost the network Rx signal.
OOF The controller card detects a framing loss from the network.
AIS The controller card is receiving an AIS (blue) alarm condition from the network.
AIS alarms occur when consecutive 1010s are received in the information bits.
This indicates that
The controller card is receiving an AIS (blue) alarm condition from the network.
This alarm occurs when consecutive 1010s are received in the information
bits, indicating there is a transmission fault located either at or upstream from
the transmitting terminal.
RAI The controller card is receiving an RAI (yellow) alarm from the network. This
alarm is a signal sent back toward the source of a failed transmit circuit. The
X-bits (X1 and X2) are set to zero.
IDLE The controller card detects an idle sequence from the network.
- M13 Multiplexer 1
- User Manual 1
- Trademarks 2
- To the Holder of the Manual 2
- Revision History 3
- Conventions 3
- Training 5
- RoHS Compliant 6
- Contents 7
- 61200290L1-1H ix 9
- Section 4 10
- Section 5 11
- Appendix A 13
- Appendix B 13
- 61200290L1-1H xv 15
- 61200290L1-1H xvii 17
- 61200290L1-1H xix 19
- Section 1 21
- Product Overview 21
- T3 OVERVIEW 22
- Network Manager 22
- 61200290L1-1H 1-3 23
- 1-4 61200290L1-1H 24
- Section 2 25
- Installation and Operation 25
- POWER UP 26
- 61200290L1-1H 2-3 27
- PWR FAIL 27
- RACKMOUNT INSTALLATION 28
- Connecting the Breakout Panel 29
- Connecting the E1 Patch Panel 29
- REAR PANEL 30
- LAN Port 31
- Modem Port 31
- DSX-3 Interfaces 31
- DSX-1/E1 Interfaces 32
- Power Connection 32
- FRONT PANEL 33
- Craft Port 33
- 2-10 61200290L1-1H 34
- 61200290L1-1H 2-11 35
- menu. Refer to “Section 5 36
- 61200290L1-1H 2-13 37
- CTRL+]) 38
- ACO Buttons 39
- LED Descriptions 39
- REPLACING OR INSTALLING CARDS 42
- Section 3 43
- Configuration 43
- menu tree 44
- 61200290L1-1H 3-3 45
- NETWORK INTERFACE 46
- DS3 Configuration 46
- 61200290L1-1H 3-5 47
- Protection Configuration 48
- Miscellaneous 49
- DS2 Configuration 49
- T1/E1 INTERFACE 49
- T1/E1 State 50
- 61200290L1-1H 3-9 51
- T1/E1 Line Coding 52
- T1/E1 Line Length 52
- T1/E1 Loopback Detection 53
- T1/E1 Circuit Protection 54
- T1/E1 Line Identification 55
- XCV Threshold 55
- SYSTEM MANAGEMENT 56
- Management Options 57
- 3-16 61200290L1-1H 58
- 61200290L1-1H 3-17 59
- 3-18 61200290L1-1H 60
- SNMP Management Options 61
- Table 3-3. Trap Descriptions 62
- 61200290L1-1H 3-21 63
- 3-22 61200290L1-1H 64
- Network Date/Time Option 65
- System Security 66
- Utilities 67
- Disabled 67
- Invisible 68
- 61200290L1-1H 3-27 69
- 3-28 61200290L1-1H 70
- 61200290L1-1H 3-29 71
- Date and Time 72
- 61200290L1-1H 3-31 73
- Equipment Identification 74
- 61200290L1-1H 3-33 75
- 3-34 61200290L1-1H 76
- UTILITIES 77
- Loading Default Settings 78
- Updating Software 79
- 3-38 61200290L1-1H 80
- Configuration Transfer 81
- Resetting the System 82
- 61200290L1-1H 3-41 83
- 3-42 61200290L1-1H 84
- 4-2 61200290L1-1H 86
- Section 4, Status - DS3 State 87
- 61200290L1-1H 4-3 87
- POWER SUPPLY STATE 88
- SYSTEM STATE 88
- Card A/Card B 89
- Protection 89
- Card Comm 90
- DS2 STATE 90
- T1/E1 STATE 90
- ACKNOWLEDGE ALARMS (ACO) 91
- 4-8 61200290L1-1H 92
- Statistics 93
- DS3 Statistics 94
- 61200290L1-1H 5-3 95
- 5-4 61200290L1-1H 96
- 61200290L1-1H 5-5 97
- 5-6 61200290L1-1H 98
- 61200290L1-1H 5-7 99
- DS2 Statistics 100
- 61200290L1-1H 5-9 101
- 5-10 61200290L1-1H 102
- 61200290L1-1H 5-11 103
- T1/E1 Statistics 104
- Performance Parameters 105
- Alarm Log 105
- PROTECTION SWITCH STATISTICS 105
- Figure 5-19. Alarm Log 106
- Section 6 107
- Loopbacks 107
- T1/E1 LOOPBACKS 108
- Data Mode 108
- Tributary 108
- Analog Network 109
- Digital Line/Net 109
- Codec Line/Net 109
- Remote Loopback 110
- CSU Loopback 110
- CSU Loopback w/BERT 110
- Line BERT 111
- DS3 LOOPBACKS 112
- Line Loopback 113
- Digital Loopback 113
- Metallic Loopback 114
- Remote All T1/E1 114
- DS2 LOOPBACKS 115
- DS2 Network 115
- 6-10 61200290L1-1H 116
- Section 7 117
- NONREDUNDANT MODE 118
- CIRCUIT FAILURE RECOVERY MODE 119
- 7-4 61200290L1-1H 120
- Section 8 121
- Power Loss Recovery 121
- POWER SUPPLY RECOVERY MODE 122
- 61200290L1-1H 8-3 123
- BATTERY BACKUP MODE 124
- Section 9 125
- Transaction Language 1 (TL1) 125
- 9-2 61200290L1-1H 126
- TL1 MESSAGES 127
- TL1 Responses 127
- 9-4 61200290L1-1H 128
- 61200290L1-1H 9-5 129
- TL1 COMMANDS 130
- 61200290L1-1H 9-7 131
- 9-8 61200290L1-1H 132
- 61200290L1-1H 9-9 133
- 9-10 61200290L1-1H 134
- TL1 Autonomous Messages 135
- 9-12 61200290L1-1H 136
- 61200290L1-1H 9-13 137
- 9-14 61200290L1-1H 138
- 61200290L1-1H 9-15 139
- TL1 ERROR CODES 140
- TL1 Editing 140
- 61200290L1-1H 9-17 141
- 9-18 61200290L1-1H 142
- should be T3 142
- 61200290L1-1H 9-19 143
- 9-20 61200290L1-1H 144
- 61200290L1-1H 9-21 145
- 9-22 61200290L1-1H 146
- should be T1 146
- 61200290L1-1H 9-23 147
- 9-24 61200290L1-1H 148
- 61200290L1-1H 9-25 149
- 9-26 61200290L1-1H 150
- 61200290L1-1H 9-27 151
- 9-28 61200290L1-1H 152
- 61200290L1-1H 9-29 153
- 9-30 61200290L1-1H 154
- Acceptance Test Procedure 155
- CONFIGURING THE SYSTEM 156
- Accessing the Craft Port 156
- Provisioning the DS3 Port 156
- 61200290L1-1H A-3 157
- , and follow the prompts 157
- Provisioning the DS1 Ports 158
- Alarm Relay Configuration 159
- VERIFYING THE DATA INTEGRITY 159
- DS1 to DS3 Head-to-Head Test 160
- DS1 to DS3 (Hard) Loopback 161
- VERIFYING ALARM NOTIFICATION 161
- Critical Alarm Relay Test 161
- Noncritical Alarm Relay Test 162
- VERIFYING SYSTEM REDUNDANCY 162
- Power Supply Redundancy 162
- 61200290L1-1H A-9 163
- Controller Card Redundancy 164
- RESTORING DEFAULT SETTINGS 165
- A-12 61200290L1-1H 166
- B-2 61200290L1-1H 168
- Appendix B, Pinouts 169
- 61200290L1-1H B-3 169
- B-4 61200290L1-1H 170
- Appendix C 171
- Specifications Summary 171
- Clocking 172
- Management 172
- Agency Approvals 173
- Environment 173
- Physical 173
- C-4 61200290L1-1H 174
- Appendix D 175
- Acronyms/Abbreviations 175
- D-2 61200290L1-1H 176
- 61200290L1-1H D-3 177
- D-4 61200290L1-1H 178
- 61200290L1-1H D-5 179
- D-6 61200290L1-1H 180
- Appendix E 181
- Glossary 181
- E-2 61200290L1-1H 182
- Appendix E, Glossary 183
- 61200290L1-1H E-3 183
- E-4 61200290L1-1H 184
- 61200290L1-1H E-5 185
- E-6 61200290L1-1H 186
- 61200290L1-1H E-7 187
- E-8 61200290L1-1H 188
- Appendix F 189
- Warranty 189
- F-2 61200290L1-1H 190
- Numerics 191
- 61200290L1-1H A-7 197
- Carrier Networks Division 198
- 901 Explorer Blvd 198
- Huntsville, AL 35806 198
Relacionado con productos y manuales para Redes ADTRAN MX2800 M13
Redes ADTRAN Vanta 1335 Manual de usuario
(4 paginas)
(4 paginas)
Redes ADTRAN TSU LT Manual de usuario
(60 paginas)
(60 paginas)
Redes ADTRAN 6310 Manual de usuario
(14 paginas)
(14 paginas)
Redes ADTRAN MX2800 M13 Manual de usuario
(45 paginas)
(45 paginas)
Redes ADTRAN 850 Manual de usuario
(76 paginas)
(76 paginas)
Redes ADTRAN BlueSecure Controller Especificaciones
(31 paginas)
(31 paginas)
Redes ADTRAN NxT1 HSSI/V-35 Manual de usuario
(16 paginas)
(16 paginas)
Redes ADTRAN NetVanta 3205 Manual de usuario
(4 paginas)
(4 paginas)
Redes ADTRAN Quad T1 IMA Especificaciones
(12 paginas)
(12 paginas)
Redes ADTRAN 1xN Manual de usuario
(12 paginas)
(12 paginas)
Redes ADTRAN TSU LT Manual de usuario
(64 paginas)
(64 paginas)
Redes ADTRAN 1200105L3 Manual de usuario
(44 paginas)
(44 paginas)
Redes ADTRAN NetVanta 3205 Manual de usuario
(2 paginas)
(2 paginas)
Redes ADTRAN MX2800 Manual de usuario
(196 paginas)
(196 paginas)
Redes ADTRAN T200 T1 HDSL4 Especificaciones
(16 paginas)
(16 paginas)
Redes ADTRAN 1248 Especificaciones
(4 paginas)
(4 paginas)
Redes ADTRAN NetVanta 160 Manual de usuario
(58 paginas)
(58 paginas)
Redes ADTRAN 6310 Manual de usuario
(4 paginas)
(4 paginas)
Redes ADTRAN 850 Manual de instrucciones
(292 paginas)
(292 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.032 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales